Step by Step:
Step 1: Plug your Ethernet cable into the Ethernet port on the back of the printer-
Step 2: Plug the power connector into the back of the printer-
Step 3: Load the roll of labels into the printer so that the labels are on the top as they come out of the printer
Step 4: Turn the power on and give the printer 30 seconds to warm up.
Step 5: The printer will automatically grab an IP address once it is plugged into your network and turned on.
Printer Software Installation
Step 1: On a workstation, log into Windows with an Administrative account.
Step 2: Insert the driver disk that came with your Bixolon 770II printer. (If it doesn’t autoplay, go ahead and start it)-
Step 3: Load the Bixolon Network Configuration Tool from the Bixolon installation disk and hit refresh to see the IP address of this printer on your network
Step 4: Adjust the IP address as needed and set it to Manual rather than DHCP. Save settings
Step 5: Start the installation by double clicking on the Installer.exe (if you get a User Account Control warning message, choose Yes to continue)-
Step 6: Choose the SRP-E770iii printer driver
Step 7: Set the name of the printer to “Barcode Printer” (printer name needs to have the word “Barcode” in it)
Step 8: When choosing the PORT, use Standard TCP/IP and enter the IP address you obtained from the Network Configuration Tool. It will come up with a window saying the device was not found.
Step 9: Ignore this and continue by clicking Next-
Step 10: It will show you a configuration window. Click Finish. This brings you back to the Printer Options window
Step 1: Open your list of Devices and Printers (Control Panel) and the Barcode printer should now be listed
Step 2: Right click on the printer and choose Printer Properties-
Step 3: Click on the Preferences at the bottom-
Step 4: Click on the Stocks Tab at the top
Step 5: Scroll down to select BIXOLON 2.5x1.0(inch) and hit Change
Step 6: Adjust the Label Width to 2.4 and click OK
Step 7: Click on the Options tab
Step 8: In the Stocks field, change the printer from using the User defined stock to Bixolon 2.5x1.0 stock that you adjusted
Step 9: Click OK to go back to the Printer Properties screen
Step 10: Click on the Advanced tab
Step 11: Click on the Printing Defaults… button at the bottom
This screen should look familiar. I’m not sure why they have the same thing in two places but they do – and they both must be adjusted.
Step 12: In the Stocks field, change the printer from using the User defined stock to Bixolon 2.5x1.0 stock that you adjusted
Step 13: Click OK
Step 14: Click OK again to close the Printer Properties window
Step 1: Log into the Evosus software with an Administrative account.
Step 2: Click on the Administration tab-
Step 3: Expand the System folder, then Evosus Defaults-
Step 4: Double click on System Parameters-
Step 5: Adjust the Label Paper Size Code field to 260-
Step 6: In the column on the left, choose Printing-
Step 7: Adjust the Barcode Label Printer Top Margin to 20 \ the Barcode Label Printer Bottom Margin to 10 \ the Barcode Label Printer Left Margin to 200 \ Barcode Label Printer Right Margin to 10.
Step 8: Make sure that the Windows Users Default Windows printer is set to a standard Network Laser Printer – NOT a receipt printer, a Multifunction printer, or this barcode label printer.
Step 9: Click Close
Printing Barcode Labels
Step 1: Choose the inventory item and click on the Barcode button
Step 2: Enter the quantity you want to print
Step 3: No need to skip any labels so click OK
Step 4: If this is the first time you’ve printed to this newly installed printer you will receive a message asking you to select a printer. Click OK
Step 5: Click on the Print Options tab
Step 6: In the upper right drop-down select your barcode printer (Select Paper Bin field will auto-fill once the printer is selected)
Step 7: Choose Print Labels – Label Printer, 2.4”x1”
Step 8: Click the Preview Report > button
- See the Troubleshooting section at the bottom if your preview shows a Red dotted line on the right hand side of the label preview
*Note: there is no Red dotted line down the right and side and the arrows in the Red rectangle below are grayed out [indicated correct formatting]
Step 9: Hit Print
You are ready to print barcodes
Red Dotted Line on the right-
Step 1: Because the Users Default Windows Printer will effect this, the First step is to Double check that the Windows Users Default Windows printer is set to a standard Network Laser Printer – NOT a receipt printer, a Multifunction printer, or this barcode label printer.
Step 2: Try adjusting your Evosus System Parameter – Label Paper Size Code to 263 or 256 and retest
Step 3: Try adjusting your Barcode Label Printer Left Margin to 100
Unless explicitly stated, this topic documents the most recent version of Evosus Business Enterprise. If you're not using the latest version, go here to download it.
Did you find it helpful?Send feedback